home *** CD-ROM | disk | FTP | other *** search
/ Software Vault: The Gold Collection / Software Vault - The Gold Collection (American Databankers) (1993).ISO / cdr11 / intmemry.zip / MEMO1120.TXT < prev    next >
Text File  |  1992-12-02  |  38KB  |  843 lines

  1.   ╔═════════════════════════════════════════════════════════════════════════╗
  2.   ║                                                                         ║
  3.   ║         ISA Bus: Computer Compatibility: 80286-Based: A-Compaq          ║
  4.   ║                                                                         ║
  5.   ╚═════════════════════════════════════════════════════════════════════════╝
  6.  
  7. 10 MHZ 286 CLONES & ABOVE BOARD 286/PLUS
  8.  
  9.   Some 10MHz 80286-based computers display intermittent Parity Check 2 or
  10.   EMM errors at power-up.  If this happens, run the SETBOARD program from
  11.   the Intel Memory Board installation disk and specify a 6-8MHz bus.
  12.  
  13. ACER
  14. ACER 286
  15.  
  16.   *CUSTOMER REPORT* of compatibility with Above Boards and Matched Memory
  17.   Classic.
  18.  
  19.   There is a jumper which indicates the amount of memory on the system
  20.   board. If this is not set correctly you will get memory size errors when
  21.   the computer powers up.
  22.  
  23. ACER 900
  24.  
  25.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  26.   Memory Classic.
  27.  
  28.   The ACER 900 is a 10MHz 80286-based system.  You will need to choose the
  29.   10MHz bus speed option in the SETBOARD program.  Probably not compatible
  30.   with the discontinued Above Board AT and PS/AT due to the fast bus speed.
  31.  
  32. ACER 910
  33.  
  34.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  35.   Memory Classic.
  36.  
  37.   Customer reported that this system is an 80286-based system running at
  38.   10MHz, but SETBOARD needs to be set for a 6-8MHz bus system.
  39.  
  40. ALR
  41. ALR DART
  42.  
  43.   *CUSTOMER REPORTS* of LIMITED COMPATIBILITY with current Above Boards and
  44.   Matched Memory Classic.  A customer reported that an Above Board does not
  45.   operate correctly with the system running at 10MHz.  The Above Board
  46.   worked fine with the system running at 8MHz.  Probably not compatible with
  47.   the discontinued Above Board AT and PS/AT when this computer is running at
  48.   the 10MHz bus speed.
  49.  
  50.   Tech Notes: Dart has 2Mb on the system board that can be configured two
  51.   different ways according to the position of SW2 on the motherboard switch
  52.   block:
  53.  
  54.   1.   Mode 1 (SW2-ON) :  system memory is 640K conv.+ 1408K ext.
  55.   2.   Mode 2 (SW2-OFF):  system memory is 512K conv.+ 1536K ext.
  56.        In Mode 2, an Above Board or Matched Memory Classic can be used to
  57.        provide conventional memory to 640K.
  58.  
  59. ALR POWERFLEX
  60.  
  61.   *MIXED CUSTOMER REPORTS* of compatibility with current Above Boards  and
  62.   Matched Memory Classic.  This is an 80286-based computer that may have an
  63.   80386SX upgrade board which fits into a proprietary slot.
  64.  
  65.   Tech Notes:  According to some customers, ALR's manual states that the
  66.   BIOS Expanded Memory Manager should be disabled before installing an Above
  67.   Board.  SETBOARD may give error messages like "incorrect bus type" if this
  68.   is not done. Disabling the ALR BIOS Expanded Memory Manager has allowed
  69.   some customers to get Above Boards working in these systems.
  70.  
  71.   Other customers have reported a "Purple Scrambled" screen when the
  72.   computer is cold booted, but sometimes works on a warm boot when an Above
  73.   Board or Matched Memory Classic is installed.
  74.  
  75.   An ALR representative has stated, "a CONDITIONAL compatibility exists with
  76.   our Powerflex line and Intel's Above Boards."  and would not go into what
  77.   the conditions were. ALR recommends customers use the proprietary ALR
  78.   memory cards.
  79.  
  80. AMDEK 286 8MHZ
  81.  
  82.   Reports of compatibility with Above Boards and Matched Memory Classic.
  83.   Intel has done limited testing with the Amdek 286 8MHz and no
  84.   compatibility issues were found.
  85.  
  86. AMI 286 12MHZ
  87.  
  88.   *CUSTOMER REPORT* of compatibility with current Above Boards and Matched
  89.   Memory Classic.  System bus speed is 12MHz.  Probably not compatible with
  90.   the Above Board AT or PS/AT due to the faster bus speed.
  91.  
  92. AMSTRAD 286
  93.  
  94.   *CUSTOMER REPORTS*  of LIMITED COMPATIBILITY with current Above Boards and
  95.   Matched Memory Classic.  This is a 12MHz 80286-based system.  The Above
  96.   Board Plus, Plus 8, and Matched Memory Classic are INCOMPATIBLE as
  97.   expanded memory but work as extended memory.  The incompatibility is with
  98.   memory boards that support an expanded memory page frame larger than 64K.
  99.   The Above Board 286 is compatible.  Probably not compatible with the Above
  100.   Board AT or PS/AT due to the faster bus speed.
  101.  
  102. AMERICAN AT
  103.  
  104.   *CUSTOMER REPORTS* of compatibility with Above Boards and Matched Memory
  105.   Classic.  The American AT is an 80286-based system.  Customers report
  106.   compatibility with the Above Board AT and PS/AT also.
  107.  
  108. ARCHE RIVAL 12MHZ
  109.  
  110.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  111.   Memory Classic in this 80286-based system.  Probably not compatible with
  112.   the discontinued Above Board AT and PS/AT due to the 12MHz bus speed of
  113.   this computer.
  114.  
  115.   This system has sockets for up to 1Mb on the system board which must be
  116.   filled before using an Above Board or Matched Memory Classic to provide
  117.   extended memory.
  118.  
  119. AST
  120. AST PREMIUM 286
  121.  
  122.   *CUSTOMER REPORTS* of compatibility with current Above Boards and the
  123.   Matched Memory Classic Boards in this 80286-based system.  You will need
  124.   to choose the 10MHz bus speed option in the SETBOARD program.  Be sure the
  125.   "zero wait state mode" on the AST system board is disabled.  Probably not
  126.   compatible with the discontinued Above Board AT and PS/AT due to the fast
  127.   10MHz bus speed.
  128.  
  129.   See also AST FastRAM which is a board that adds conventional memory and
  130.   may conflict with SOFTSET.
  131.  
  132.   One user reported that an Above Board AT worked as extended memory if the
  133.   "zero wait state" mode was disabled.  This system also takes the Intel
  134.   80287-8.
  135.  
  136.   One customer reported that the way to set the wait states is to change
  137.   jumper E2 on the AST FASTRAM Memory Card:
  138.  
  139.       Jumper on E2 sets 0 wait states
  140.       Jumper off of E2 sets 1 Wait State
  141.  
  142.   The customer read it directly from the AST manual.  It was the only
  143.   reference to wait states he could find in the manual. Changing the jumper
  144.   fixed the problem in this case.  An Above Board wasn't seen on POST with
  145.   E2 on.  Customer removed E2 and the Above Board counted on POST.
  146.  
  147. AST 123X WORKSTATION
  148.  
  149.   *CUSTOMER REPORTS* of compatibility with Current Above Boards and the
  150.   Matched Memory Classic in this 80286-based system as expanded memory.
  151.   Intel has not received any reports one way or the other about extended
  152.   memory compatibility issues.
  153.  
  154.   Tech Notes:  It was reported that SOFTSET gave the error "incompatible
  155.   board..." in this computer.  If this happens, it will be necessary to
  156.   manually install the EMM.SYS device driver for expanded memory.  SETBOARD
  157.   showed that I/O addresses 218 & 258 were being used besides the I/O
  158.   address the Above Board occupied.  This system has only two expansion
  159.   slots, built in VGA video support, and comes without a FastRAM board
  160.   installed.
  161.  
  162. AT JET
  163.  
  164.   *CUSTOMER REPORT* of compatibility with current Above Boards and Matched
  165.   Memory Classic in this 80286-based computer.  This system apparently has a
  166.   12MHz data bus.  An odd symptom of this computer is that TESTAB would lock
  167.   up when the Above Board was set for a 6/8MHz bus.  Probably not compatible
  168.   with the discontinued Above Board AT and PS/AT due to the 12MHz data bus
  169.   of this computer.
  170.  
  171. AT&T
  172. AT&T 6286
  173.  
  174.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  175.   Memory Classic.
  176.  
  177.   Tech Notes:  This is a 12MHz 80286-based system with 1Mb on the system
  178.   board.  Make sure SETBOARD configures the Above Board or Matched Memory
  179.   Classic board for 12MHz bus operation.  Probably not compatible with the
  180.   discontinued Above Board AT and PS/AT due to the fast bus speed.
  181.  
  182.   We have mixed reports about configuring an Above Board or Matched Memory
  183.   Classic board as extended memory in this system.  In some cases it was
  184.   necessary to set the extended memory starting address at 1024K in
  185.   SETBOARD.  In other cases a starting address of 1280K worked.  In most
  186.   cases, a starting address of 1408K will work fine.
  187.  
  188. AT&T 6286 WGS
  189.  
  190.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  191.   Memory Classic.
  192.  
  193.   Tech Notes:  This is a 12MHz 80286-based system with 1Mb on the system
  194.   board.  Make sure SETBOARD configures the Above Board or the Matched
  195.   Memory Classic board for 12MHz bus operation.  This computer is probably
  196.   not compatible with the discontinued Above Board AT and PS/AT due to the
  197.   fast bus speed.
  198.  
  199.   We have mixed reports about configuring a current Above Board or Matched
  200.   Memory Classic board as extended memory in this system.  In some cases it
  201.   was necessary to set the extended memory starting address at 1024K in
  202.   SETBOARD.  In other cases a starting address of 1280K worked.  In most
  203.   cases, a starting address of 1408K will work fine.
  204.  
  205. AT&T 6300 PLUS
  206.  
  207.   Above Boards and Matched Memory Classic are INCOMPATIBLE with this system.
  208.  
  209.   This is an 80286-based system but there are no AT 16-bit bus slots.  The
  210.   AT&T 6300 Plus does have some 8-bit bus slots but they are not IBM
  211.   compatible.
  212.  
  213. AT&T 6310
  214.  
  215.   Compatible with current Above Boards and Matched Memory classic.  The AT&T
  216.   Technical Lab claims compatibility with the discontinued Above Board 286,
  217.   PS/286, AT, & PS/AT also.
  218.  
  219.   This 80286-based system has an 8Mhz, 1 wait state data bus.  Uses Phoenix
  220.   BIOS, 230W power supply, has programmable diagnostics. Comes with 512K on
  221.   the motherboard and is expandable to 1Mb.
  222.  
  223. AT&T 6312
  224.  
  225.   *CUSTOMER REPORTS* of compatibility with current Above Boards and Matched
  226.   Memory Classic in this 80286-based computer.  AT&T has approved the Above
  227.   Board Plus.
  228.  
  229.   Tech Notes:  Specify a 12MHz bus and 150ns chip speed in SETBOARD.  This
  230.   12MHz 80286-based system comes with a 1Mb system board configured as 640K
  231.   base & 384K extended.  Probably not compatible with the discontinued Above
  232.   Board AT and PS/AT due to the fast bus speed.
  233.  
  234. BENTLEY 286
  235.  
  236.   *CUSTOMER REPORTS* of compatibility with Above Boards and Matched Memory
  237.   Classic in this 80286-based computer.
  238.  
  239.   Tech Notes:  This computer has 1Mb on the system board that can be
  240.   configured as 640K conv, 384K extended or 512K conv, 512K extended.  The
  241.   system speed is 6-10MHz selectable.
  242.  
  243. CITIZEN 286
  244.  
  245.   *CUSTOMER REPORT* of INCOMPATIBILITY with Above Boards and Matched Memory
  246.   Classic.  Report indicated that this system runs at 12.5MHz, 0 wait
  247.   states.  A system running at 0 wait states violates the IBM specification
  248.   of 1 wait state and is not fully IBM compatible.  Intel classic bus memory
  249.   boards require the IBM standard of 1 wait state.
  250.  
  251. COMMODORE PC 40 III
  252.  
  253.   *CUSTOMER REPORT* of LIMITED COMPATIBILITY with Above Boards and Matched
  254.   Memory Classic.
  255.  
  256.   Commodore mentions the Intel Above Board Plus for memory expansion in the
  257.   owner's manual for this machine.
  258.  
  259.   This is a 6/8/12MHz selectable system.  It is necessary to set the system
  260.   speed to 8MHz when using an Above Board or Matched Memory Classic in this
  261.   computer.  When this system is running at 12MHz, the data bus runs at 0
  262.   wait states and an Above Board or Matched Memory Classic board will not
  263.   function properly.  A system running at 0 wait states violates the IBM
  264.   specification of 1 wait state and is not fully IBM compatible.  Intel
  265.   Above Boards require the IBM standard of 1 wait state.
  266.  
  267. COMPAQ
  268. COMPAQ DESKPRO 286
  269.  
  270.   Compatible with current Above Boards and Matched Memory classic.  Also
  271.   compatible with the discontinued Above Board 286, PS/286, AT, and PS/AT.
  272.  
  273. COMPAQ DESKPRO 286 (12MHZ)
  274.  
  275.   Compatible with current Above Boards and Matched Memory Classic.  Also
  276.   compatible with the discontinued Above Board 286, PS/286, AT, and PS/AT.
  277.  
  278.   This 80286-based system has 8 rows of sockets on the motherboard that will
  279.   accept either 64K DRAMS or 256K DRAMS (120ns).  There is also 128K of
  280.   memory soldered onto the system board.
  281.  
  282.   Maintains a standard 8MHz bus.  Uses an Intel 80287-8 math coprocessor.
  283.  
  284. PARITY CHECK 2 ERROR IN DESKPRO 286 12 MHZ
  285.  
  286.   If you get this message after installing an Above Board or Matched Memory
  287.   Classic, it is likely you have overlapping conventional memory, (both the
  288.   Above Board or Matched Memory Classic, and the Compaq motherboard are
  289.   trying to supply conventional memory).
  290.  
  291.   There are two ways to correct this problem:
  292.  
  293.   1.   The first is to temporarily disable the Compaq motherboard memory
  294.        down to 256K or 512K. (If the error is Parity Check 2 40000,
  295.        disable motherboard memory down to 256K, if the error is Parity
  296.        Check 2 80000, then disable motherboard memory down to 512K).
  297.        There are three steps to this procedure:
  298.  
  299.        a.   The Compaq motherboard switch block is located on the front
  300.             left corner of motherboard.
  301.  
  302.        SWITCHES   2      3     MEMORY SIZE
  303.                  ON     ON     Disable RAM and ROM
  304.                  ON     OFF    Limit motherboard to 256K
  305.                  OFF    ON     Limit motherboard to 512K
  306.                  OFF    OFF    Enable all base memory, 640K max
  307.  
  308.        b.   Rerun SETBOARD.  Tell the Above Board or Matched Memory
  309.             Classic to supply NO conventional memory.
  310.        c.   Set Compaq motherboard switches back to 640K.
  311.  
  312.   2.   The second method of eliminating this problem is to find a way to
  313.        rerun SETBOARD without first correcting the conventional memory
  314.        overlap. There are four steps to this approach:
  315.  
  316.        a.   Temporarily remove the Above Board or Matched Memory Classic
  317.             from the system.
  318.        b.   Copy the SETBOARD.EXE program from the Above Board / Matched
  319.             Memory Classic installation diskette to the hard disk.
  320.        c.   Reinstall the board.
  321.        d.   Rerun SETBOARD from the hard disk and set the Above Board or
  322.             Matched Memory Classic to supply NO conventional memory.
  323.  
  324.   NOTE:     Overlapping conventional memory causes Parity Check 2 errors
  325.             during floppy disk accesses.  If the Above Board or Matched
  326.             Memory Classic is removed while SETBOARD is being copied to
  327.             the hard disk, there will not be a Parity Check 2 error. When
  328.             the Board is reinstalled and SETBOARD is run from the hard
  329.             disk, SETBOARD should be able to successfully reprogram our
  330.             board without a parity error occurring.  People who do not
  331.             feel comfortable changing motherboard switches should use
  332.             this approach.
  333.  
  334. EXTENDED MEMORY IN DESKPRO 286 (12MHZ)
  335.  
  336.   If you use an Above Board or Matched Memory Classic to supply extended
  337.   memory, you have two options. They are:
  338.  
  339.   1.   Fill TWO rows on the motherboard with 256K chips for a total of
  340.        640K conventional memory, (128K on the motherboard is not readily
  341.        visible, but is there none the less).  You should have SIX rows of
  342.        empty sockets on the motherboard.
  343.  
  344.        Switches 4 and 5 on SW1, (near the front left corner of the
  345.        motherboard),  should both be ON.  This says that the motherboard
  346.        WILL NOT supply ANY extended memory.
  347.  
  348.        Start the Above Board or Matched Memory Classic extended memory at
  349.        1024K, (1.0M), in SETBOARD.
  350.  
  351.   2.   Fill all EIGHT rows on the motherboard with 256K chips for a total
  352.        of 640K of conventional memory and 1536K of extended memory on the
  353.        motherboard.
  354.  
  355.        Switches 4 and 5 on SW1 should both be OFF.  This says the
  356.        motherboard will supply extended memory from 1Mb to 2.5Mb.  Start
  357.        the Above Board or Matched Memory Classic extended memory at
  358.        2560K, (2.5M) in SETBOARD.
  359.  
  360.   Any combination BETWEEN these two configurations is not allowed, and the
  361.   Deskpro will not "see" our board.
  362.  
  363. COMPAQ PORTABLE 286
  364.  
  365.   Compatible with current Above Boards and Matched Memory Classic.  Also
  366.   compatible with the discontinued Above Board 286, PS/286, AT and PS/AT.
  367.  
  368. COMPAQ PORTABLE II
  369.  
  370.   Compatible with current Above Boards and Matched Memory Classic in the 16-
  371.   bit slot of this 80286-based computer.  Also compatible with Above Board
  372.   AT &  PS/AT in the 16-bit slot.
  373.  
  374.   This computer has only one 16-bit slot and an 8-bit slot.  Above Boards
  375.   and Matched Memory Classic can only be used in 8-bit slots if the
  376.   computer's processer is an 8088 or an 8086.
  377.  
  378.   System may have optional extended memory on a board under the motherboard.
  379.  
  380. COMPAQ PORTABLE III
  381.  
  382.   Compatible with current Above Boards and Matched Memory Classic.  The
  383.   Above Board AT and PS/AT are NOT reliable in this 80286-based system.
  384.  
  385.   An expansion chassis is required for any add-in boards.  Inserting a board
  386.   into an expansion chassis must be done with care to avoid damage to the
  387.   board,  it's a bit tricky to get it installed just right.  Standard ports
  388.   are defaulted to LPT1 and COM1.
  389.  
  390.   This system requires an Intel 80287-8.
  391.  
  392. COMPAQ 286N
  393.  
  394.   Compatible with current Above Boards and Matched Memory Classic.
  395.   It is necessary to disable Compaq's CEMMP if installing an Above Board or
  396.   Matched Memory Classic as expanded memory.  If installing an Above Board
  397.   or Matched Memory Classic as extended memory, choose an extended memory
  398.   starting address of 1024K, (1.0M) in SETBOARD.
  399.   This system uses the Intel 287XL or 80287-8.  There is only ONE switch,
  400.   switch 5 on a block of 6, that is used to toggle between 8 and 12 MHz math
  401.   coprocessors.
  402.  
  403.   System specs:
  404.   CPU       80286 10MHz (Soldered).
  405.   RAM       640K conventional, (also 256/512), 384K expanded built in.
  406.   MCP       287XL or 287-8 socket
  407.   Rsv Mem   Video ROM at C000-C5FFF. The drive controller (on the
  408.             motherboard) uses no reserved memory in the C000-DFFF
  409.             range...built into system ROM.
  410.   Drives    1.44 MB floppy.
  411.   Slots     2 full length 16-bit ISA (classic) expansion bus slots. One
  412.             dedicated Compaq memory slot.
  413.   Video     VGA built in. No external video port available.
  414.   Ports     Built in serial port - can be set to COM1 (3F8/IRQ4) or
  415.             disabled.  Built in parallel port - can be set to LPT1 (3BC),
  416.             LPT2(378) or LPT3(278). Mouse port.
  417.  
  418.   Intel RapidCAD Performance Brief
  419.  
  420.   Intel RapidCAD Engineering CoProcessor
  421.   Performance Brief
  422.  
  423.   Table of Contents
  424.  
  425.   Introduction                                         1
  426.  
  427.   The Intel RapidCAD Engineering CoProcessor           1
  428.  
  429.   Intel RapidCAD Engineering CoProcessor Performance
  430.   Summary                                              2
  431.  
  432.   Test Configurations                                  2
  433.  
  434.   Benchmark Tests                                      2
  435.        DOS Standard Benchmark Tests                    3
  436.        UNIX Standard Benchmark Test                    3
  437.        DOS Application Benchmark Tests                 4
  438.  
  439.   Table 1- DOS Application Benchmark Results           7
  440.  
  441.   Table 2- DOS Standard Benchmark Results              10
  442.  
  443.   Table 3- UNIX Benchmark Results                      11
  444.  
  445.   Introduction
  446.  
  447.   Benchmarks are intended to give a standard measure of performance that can
  448.   be used to predict how well application code will execute.  These
  449.   benchmark programs should be representative of the intended applications.
  450.   However, the performance measured is often the combined characteristic of
  451.   a given computer architecture and many other tightly-coupled system
  452.   software and hardware constituents.  The memory and I/O subsystem design,
  453.   as well as the operating system and the software development tools, may
  454.   dominate the results and make the comparison difficult.
  455.  
  456.   This document contains performance measurements in both DOS and UNIX
  457.   operating environment, which can be used as predictors of real application
  458.   performance.
  459.  
  460.   The Intel RapidCAD Engineering CoProcessor
  461.  
  462.   The Intel RapidCAD Engineering CoProcessor, the newest member of Intel386
  463.   product family, is the highest performance floating-point upgrade for
  464.   Intel386 DX microprocessor-based systems.  Manufactured using high speed
  465.   CHMOS V technology, the Intel RapidCAD Engineering CoProcessor is a two
  466.   chip set: RapidCAD-1 and RapidCAD-2.  The first chip, RapidCAD-1, replaces
  467.   the Intel386 DX microprocessor.  It is pin compatible with the Intel386DX
  468.   microprocessor and integrates the central processing unit (CPU) and
  469.   floating point unit (FPU) on the same silicon die reducing the inter-chip
  470.   communication delays.  Eliminating the communication overhead of
  471.   transferring commands, data and results over the I/O bus between the CPU
  472.   and the math coprocessor (MCP), enables exceptional floating-point
  473.   performance.  The second chip, RapidCAD-2, is installed in the Intel387 DX
  474.   Math CoProcessor socket.  It provides hardware compatibility with the
  475.   unmasked floating-point exception reporting in standard Intel386
  476.   microprocessor-based architectures.  The floating-point and binary coded
  477.   decimal data formats fully conform to the ANSI/IEEE Standard 754-1985 for
  478.   binary floating-point arithmetic.  The Intel RapidCAD Engineering
  479.   CoProcessor is binary compatible with the Intel386DX microprocessor and
  480.   the Intel387 DX, Intel387SX, Intel287XL and 8087 Math CoProcessors.
  481.  
  482.   Intel RapidCAD Engineering CoProcessor Performance Summary
  483.  
  484.   Benchmark results confirm that the RapidCAD Engineering CoProcessor runs
  485.   floating-point code from 56 to 146 percent faster than the Intel386 DX
  486.   microprocessor with the Intel 387DX math CoProcessor.  This exceptional
  487.   floating-point performance translates into excellent performance
  488.   improvement for applications which makes extensive use of the floating-
  489.   point instruction set.  Application benchmarks show performance
  490.   improvement averaging 30 to 40 percent, and as high as 67 percent for 3D
  491.   Studio and MathCAD. The Intel RapidCAD Engineering CoProcessor's
  492.   exceptional floating-point performance translates into real time savings
  493.   for the engineering professional using an Intel386 DX microprocessor-based
  494.   system running CAD or scientific application software.
  495.  
  496.   Test Configurations
  497.  
  498.   The DOS tests were performed on a COMPAQ DeskPro 386/33MHz.
  499.  
  500.   Memory         640KB base and 7MB extended
  501.   Video          COMPAQ mother board VGA
  502.   Disk           80MB IDE
  503.  
  504.   Operating      Compaq Personal Computer DOS 3.31
  505.   System         Windows 3.0
  506.  
  507.   The UNIX tests were performed on a COMPAQ SystemPro 386/33MHz
  508.  
  509.   Memory         640KB base and 7MB extended
  510.   Video          COMPAQ mother board VGA
  511.   Disk           COMPAQ Disk Array
  512.  
  513.   Operating      
  514.   System         AT&T UNIX System V/386 Release 4.0 Version 2.0
  515.  
  516.   Benchmark Tests:
  517.   Standard benchmark tests were used to separately evaluate integer and
  518.   floating-point performance.  DOS and UNIX standard benchmark tests were
  519.   run.  All applications tested run under DOS or Windows.  Application
  520.   performance was estimated using two kinds of tests.  A subset of the BYTE
  521.   Application Benchmark Version 2.0 and the AutoCAD Benchmark Test Series
  522.   Distributed by the AutoCAD Users Group of San Diego Version 1.1, were used
  523.   as part of the application benchmark testing.  They run automatically,
  524.   using the system clock to measure the execution time.  For applications
  525.   where an automatically running test was not available, such as AutoShade
  526.   and 3D Studio, typical commands which use RapidCAD's floating-point
  527.   capability were run and the execution time was measured with a stop watch.
  528.  
  529.   For each test there are two sets of results, one obtained with the
  530.   Intel386 DX microprocessor and Intel387 DX Math CoProcessor, the other
  531.   with Intel RapidCAD Engineering CoProcessor.  A performance index is
  532.   calculated in each case showing the relative execution speed delta using
  533.   the Intel RapidCAD Engineering CoProcessor vs. the Intel 386 DX
  534.   microprocessor and the Intel387 DX Math CoProcessor.
  535.  
  536.   DOS Standard Benchmark Tests
  537.  
  538.   Dhrystone is an industry-standard benchmark test designed to measure
  539.   system programming performance.  It includes weighted percentages of
  540.   procedure calls, loops, integer assignments, integer arithmetic and
  541.   logical operations.  The result is CPU speed expressed in Dhrystones/sec.
  542.   Sixteen-bit Dhrystone Version 2.0 and a 32-bit Dhrystones Version 2.1 were
  543.   used.
  544.  
  545.   Whetstone is an industry-standard benchmark test designed to predict
  546.   performance in a floating-point intensive enviroment.  It is a synthetic
  547.   mix of floating-point and integer arithmetic, transcendental functions,
  548.   floating-point array computations, and floating-point subroutine calls,
  549.   based on statistical analysis of scientific FORTRAN programs.  The result
  550.   is expressed in KIPS (kilo instructions per second).  Single and double
  551.   precision 16- and 32-bit Whetstones were used.  In addition the Microway
  552.   Whetstone benchmark was run to give a more comprehensive measure of
  553.   floating-point performance in 32-bit protected mode.
  554.  
  555.   UNIX Standard Benchmark Test
  556.  
  557.   The SPEC benchmark Suite Release 1.0 consists of 10 FORTRAN and C
  558.   benchmarks that are intended to be meaningful samples of applications
  559.   which perform fixed- and floating-point logical and arithmetic operations
  560.   as well as disk I/O in a technical environment.  Many of these benchmarks
  561.   have been derived from publicly available application programs.
  562.  
  563.   The benchmark suite may be divided in two separate benchmark suites to
  564.   distinguish between the integer and floating-point performance.  This
  565.   allows for better performance prediction under different operating
  566.   environments.  The integer performance represents a more appropriate
  567.   instruction mix for commercial applications in a business environment.
  568.   The floating-point performance can be used to predict the system
  569.   performance in a technical environment for scientific and engineering
  570.   applications.  The global SPEC index, SPECmark, is the geometric mean of
  571.   all test results.  The SPEC integer index, SPECint, represents the
  572.   geometric mean of the results for the four C programs.  The SPEC floating-
  573.   point index, SPECfp, represents the geometric mean of the results of the
  574.   six FORTRAN programs.
  575.  
  576.   DOS Application Benchmark Tests
  577.  
  578.   Generic 3D Drafting Version 1.1
  579.   The model BEARING.3DD was used to execute a perspective change (VIEW,
  580.   Perspect VP) with the coordinates 0,0,-25 and 350,400,400.  The elapsed
  581.   time was measured with a stop watch.
  582.  
  583.   AutoCAD Release 11
  584.   The BYTE Application Benchmark Version 2.0 test and the Benchmark Test
  585.   Series Distributed by The AutoCAD Users Group of San Diego were used.
  586.   This series of tests execute a typical mix of commands that might be
  587.   issued by an AutoCAD user.  These tests measure the elapsed time using the
  588.   system clock.
  589.  
  590.   AutoCAD Release 11 Advanced Modelling Extension (AME)
  591.   A simple model was created (FLANGE.DWG) to test solids subtract, mesh and
  592.   filled shade.  The elapsed time was measured with a stop watch.
  593.  
  594.   AutoShade with RenderMan Release 2.0
  595.   The sample film KITCHEN.FLM was used to test full shade and RenderMan
  596.   render.  The elapsed time was measured with a stop watch.
  597.  
  598.   3D Studio Release 1.0
  599.   The sample models CITY.3DS, RACECAR.3DS, and STILLIFE.3DS were used to
  600.   test the render function, with the following setting: Shading limit =
  601.   Phone; Anti-Alias= High; Shadows = On; Mapping = On; Hidden Geometry =
  602.   Hide; Render Output = Display.  The elapsed time was measured with a stop
  603.   watch.
  604.  
  605.   Cadkey 386 Version 4
  606.   To measure performance with the standard drawing functions an array of
  607.   1000 ellipses was first drawn and then deleted.  To test the performance
  608.   of advanced solid functions the sample model SOLID4.PRT was used.  A
  609.   complex process performning solid boolean operations (solid subtraction
  610.   and plane sectioning), mass properties and a smooth shading followed by
  611.   the rendering (with Shading = Phong) of the resulting image were
  612.   performed.  The elapsed time was measured with a stop watch.
  613.  
  614.   MicroStation PC Version 4.0
  615.   The sample ORBITER.DGN model was used for hidden lines removal, smooth
  616.   shading, phong shading, stereoscopic rendering and a zoom out.  The
  617.   elapsed time was measured with a stop watch.
  618.  
  619.   Upfront Version 1.0
  620.   The sample drawing LIBRARY.UPF was used and two view change tests were
  621.   done: from initial view to Birdseye and back.  The elapsed time was
  622.   measured with a stop watch.
  623.  
  624.   Mathematica 2.0 for DOS 386/7 and Mathematica 2.0 for Windows
  625.   The execution time of Plot3D[10 sin[x+Sin[y]], {x, -10, 10}, {y, -10, 10},
  626.   PlotPoints -> 80] was measured with a stop watch.
  627.  
  628.   MathCAD 2.50
  629.   The BYTE Application Benchmark Version 2.0 test was used.  It calculates a
  630.   convolution integral and evaluates an iterative function system.  This
  631.   test measures the elapsed time using the system clock.
  632.  
  633.   PC-Matlab Ver 3.5g
  634.   The BYTE Application Benchmark Ver 2.0 test was used.  This test performs
  635.   a mix of matrix and signal processing operations.  This test measures the
  636.   elapsed time using the system clock.
  637.  
  638.   SPSS/PC + V4.0.1
  639.   A statistics example with 1473 cases was used for descriptive statistics
  640.   (means) and a graphic representation with Harvard Graphics.  The elapsed
  641.   time was measured with a stop watch.
  642.  
  643.   STATGRAPHICS Ver 4.0
  644.   Three randomly gneerated 1000 samples series were used for summary
  645.   statistics (STATS) and multiple regression.  The elapsed time was measured
  646.   with a stop watch.
  647.  
  648.   Lotus 1-2-3 Release 3
  649.   The BYTE Application Benchmark Ver 2.0 test was used.  The test loads and
  650.   recalculates a spreadsheet based on the Savage formula, then it runs a
  651.   macro that performs a binary goal seek.  Additionally, a large block of
  652.   text data is loaded, copied and then saved.  This test measures the
  653.   elapsed time using the system clock.
  654.  
  655.   Excel Version 3.0
  656.   The BYTE Application Benchmark Ver 2.0 test was used.  The test is similar
  657.   to the one for Lotus 1-2-3.  It loads and recalculates a spreadsheet based
  658.   on the Savage formula, then it runs a macro that performs a binary goal
  659.   seek.  This test measures the elapsed time using the system clock.
  660.  
  661.   Table 1- DOS Application Benchmark Results
  662.  
  663.   DOS Application(1)       Intel386DX     Intel   Percentage
  664.                              CPU and      RapidCAD     Performance
  665.                            Intel387DX     Engineer-    Improvement
  666.                                MCP        ing Co-
  667.                                           Processor
  668.  
  669.   Generic 3D Drafting
  670.     Ver 1.1                33.46          25.53   31%
  671.  
  672.   AutoCAD Release 11
  673.   Byte Magazine Benchmark Test
  674.     Redraw (sec)           6.03           5.60         8%
  675.     Pan (sec)              38.50          30.03   28%
  676.     Zoom (sec)             46.91          34.93   34%
  677.     Hide (sec)             70.57          48.44   46%
  678.     Regen (sec)            27.95          20.76   35%
  679.  
  680.   San Diego Benchmark Test
  681.     Total time (sec)       339.00         295.44  15%
  682.     Phase 1, draw (sec)    45.04          41.03   10%
  683.     Phase 1, ZOOM (sec)    2.69           2.14         26%
  684.     Phase 1, REGEN (sec)   5.00           3.84         30%
  685.     Phase 2, draw (sec)    56.14          50.97   10%
  686.     Phase 2, ZOOM (sec)    7.85           6.10         29%
  687.     Phase 2, REGEN (sec)   9.83           7.58         30%
  688.     Phase 3, draw (sec)    66.57          60.53   10%
  689.     Phase 3, ZOOM (sec)    13.07          10.27   27%
  690.     Phase 3, REGEN (sec)   20.93          16.25   29%
  691.     3D Module (sec)        12.75          11.42   12%
  692.     3D VPOINT (sec)        0.93           0.77         21%
  693.     3D HIDE (sec)          11.92          9.89         21%
  694.     AutoLISP calculation
  695.     (sec)                  2.15           1.92         12%
  696.  
  697.   AutoCAD Release 11 AME
  698.     Subtract (sec)         36.00          31.00   16%
  699.     Mesh (sec)             30.86          21.34   45%
  700.     Shade (sec)            9.52           6.12         56%
  701.  
  702.   AutoShade Release 2.0
  703.     Full shade (sec)       16.42          12.26   34%
  704.     Render (sec)           178.49         109.18  63%
  705.  
  706.   3D Studio Release 1.0 (Render)
  707.     CITY.3DD (sec)         369.00         223.00  65%
  708.     RACECAR.3DD (sec)      1244.00        746.00  67%
  709.     STILLIFE.3DD (sec)     473.00         292.00  62%
  710.  
  711.   Cadkey 386 Version 4
  712.     Draw ellipses (sec)    19.16          13.79   39%
  713.     Delete ALL (sec)       14.84          11.33   31%
  714.     Complex solids process
  715.     (sec)                  88.00          58.09   51%
  716.     Dashed smooth shading
  717.     (sec)                  85.00          59.86   42%
  718.     Smooth shading display
  719.     (sec)                  64.00          39.87   61%
  720.  
  721.   MicroStation PC
  722.     Render-Hidden lines(sec)130.00        98.00   39%
  723.           -Smooth (sec)    106.00         77.00   38%
  724.           -Phone (sec)     160.00         108.00  48%
  725.           -Stereo (sec)    211.00         154.00  37%
  726.     Zoom out (sec)         16.00          11.00   45%
  727.  
  728.   Mathematica 2.0 for DOS 386/7
  729.     Plot3D (sec)           119.10         103.38  15%
  730.  
  731.   Mathematica 2.0 for Windows
  732.     Plot3D (sec)           114.53         89.17   28%
  733.  
  734.   MathCAD 2.50
  735.   BYTE Magazine Benchmark Test
  736.     Convolve               41.66          36.67   14%
  737.     IFS                    23.77          19.65   21%
  738.  
  739.   PC-MATLAB Ver 3.5g
  740.   BYTE Magazine Benchmark Test
  741.     Matrix (sec)           8.34           5.49         52%
  742.     Signal processing (sec)41.06          24.54   67%
  743.  
  744.   SPSS/PC+ V4.0.1
  745.     Means (sec)            14.54          12.15   20%
  746.     GRAPH (sec)            10.19          9.23         10%
  747.  
  748.   STATGRAPHICS Ver 4.0
  749.     Summary statistics(sec)7.61           6.00         27%
  750.     Multiple regression(sec)11.41         8.19         39%
  751.  
  752.   Lotus 1-2-3 R3.0
  753.   BYTE Magazine Benchmark Test
  754.     Load Savage (sec)      8.00           7.00         14%
  755.     Calc Savage (sec)      19.00          15.00   27%
  756.     Run Goalseek (sec)     13.00          11.00   18%
  757.     Load Block (sec)       8.00           7.00         14%
  758.     Copy Block (sec)       28.00          25.00   12%
  759.     Save Block (sec)       12.00          11.00   9%
  760.  
  761.   Excel Version 3.0
  762.   BYTE Magazine Benchmark Test
  763.     Open Savage (sec)      18.00          17.00   6%
  764.     Calc Savage (sec)      73.00          55.00   33%
  765.     Run Goalseek (sec)     19.00          18.00   6%
  766.  
  767.   (1) All applications were run under Compaq Personal Computer
  768.        DOS 3.31
  769.  
  770.   Table 2- DOS Standard Benchmark Results
  771.  
  772.   DOS Benchmark            Intel386DX     Intel   Percentage
  773.                              CPU and      RapidCAD     Performance
  774.                            Intel387DX     Engineer-    Improvement
  775.                                MCP        ing Co-
  776.                                           Processor
  777.  
  778.   32-bit Performance
  779.  
  780.   Dhrystone (Dhrystone/sec)
  781.     Version 2.1            15888.10       18274.90          15%
  782.  
  783.   Whetstone (KWhet/sec)
  784.     Single Precision       3813.00        6120.00      61%
  785.     Double Precision       3286.00        5299.00      61%
  786.  
  787.   Microway (KWhet/sec)
  788.     Whetstone              3720.90        6481.00      74%
  789.     WhetMat                733.94         1625.90      122%
  790.     WhetScale              1422.20        3492.50      146%
  791.     WhetTrans              1051.80        1733.20      65%
  792.  
  793.   16-bit Performance
  794.  
  795.   Dhrystone (Dhrystone/sec)
  796.     Version 2.0            12955.50       13704.50          6%
  797.        
  798.   Whetstone (KWhet/sec)
  799.     Single Precision       2272.00        3571.00      57%
  800.     Double Precision       2000.00        3125.00      56%
  801.  
  802.   Note:  The loosely copuled internal architecture makes RapidCAD more
  803.   sensitive to wait states than Intel386 DX CPU.  Therefore in systems
  804.   without cache and more than three wait states for memory accesses, the
  805.   integer performance of RapidCAD becomes lower than the integer performance
  806.   of Intel386 DX Microprocessor.  However this is not likely to occur, since
  807.   almost all Intel386 DX microprocessor-based PCs have cache in their
  808.   configuration.
  809.  
  810.   Additional wait states in the MCP I/O cycles may considerably increase
  811.   RapidCAD's floating-point performance relative to Intel386 DX
  812.   microprocessor and Intel387 DX Math CoProcessor.
  813.  
  814.   Table 3- UNIX Benchmark Results
  815.  
  816.   UNIX Benchmark           Intel386DX     Intel   Percentage
  817.                              CPU and      RapidCAD     Performance
  818.                            Intel387DX     Engineer-    Improvement
  819.                                MCP        ing Co-
  820.                                           Processor
  821.  
  822.   SPEC 1.0
  823.     001.gcc (sec)          239.00         210.00       14%
  824.     008.espresso (sec)     336.00         270.00       24%
  825.     013.spice2g6 (sec)     5227.00        3679.00      42%
  826.     015.doduc (sec)        684.00         328.00       109%
  827.     020.nasa7 (sec)        5847.00        3561.00      64%
  828.     022.li (sec)           803.00         671.00       20%
  829.     023.eqntott (sec)      245.00         207.00       18%
  830.     030.matrix300 (sec)    1120.00        672.00       67%
  831.     042.fpppp (sec)        1000.00        395.00       253%
  832.     047.tomcatv (sec)      1138.00        552.00       106%
  833.  
  834.   SPECmark                 2.829          4.410        56%
  835.        
  836.   SPECint                  2.827          3.364        19%
  837.  
  838.   SPECfp                   2.830          5.283        87%
  839.  
  840.  
  841. ══════════════════════════════════════════════════════════════════════════════
  842. End of file                 Intel FaxBack # 1120          December 2,1992
  843.